Results for conrad components data gateway usb uart compatible with c control
Gossen Metrawatt USB-PACK interface adapter for USB-connection Compatible with METRAHIT CAL
Click For Info
433 MHz AM HF interface supported directly from the operating system. Hard-wired with port 6 transmitter and port 7 receiver. This interface is compatible with many wireless radio switches on the market. It enables a number of remotely switchable sockets to be controlled from the C-Control....
Click For Info
433 MHz AM HF direct from the operating system supported interface. Hard-wired with port 3 transmitter and port 2 receiver. This interface is compatible with many wireless radio-switches on the market. It enables many remotely-switchable sockets to be controlled from the C-Control. Ready-built with...
Click For Info
The C-Control Project Board is a convenient alternative to the evaluation board The C-Control Project Board PRO includes the major components needed to operate the C-PRO Control Unit. on the Project Board a voltage supply (USB / AC adapter), interface converter (RS232) and a large hole grid for...
Click For Info
The C-Control Project Board is a convenient alternative to the evaluation board The C-Control Project Board PRO includes the major components needed to operate the C-PRO Control Unit. on the Project Board a voltage supply (USB / AC adapter), interface converter (RS232) and a large hole grid for...
Click For Info
For connection of Dallas Semiconductor 1-Wire components to a C-Control I unit over the I²C-Bus. The 1-Wire components can be optionally connected through a RJ12 socket (1-W, GND) or a 3pin multi plug connection (1-W, GND). This module can be secured in the case by mounting angles, in the same...
Click For Info
EW-7811Un is a nano USB wireless adapter that supports maximum range and speed. Despite the size, this tiny USB adapter supports higher data rate of up to 150Mbps when connecting with wireless 802.11n device which is 3 times faster than your normally 11g connection. You can just plug it into...
Click For Info
DCF 77 receiver components in a weather-proof case in accordance with IP54, can be used anywhere that DCF reception is not possible, e.g because of steel reinforced concrete, electrical interference fields from machines and computers. The receiver unit can be turned through 360° and therefore...
Click For Info
To connect the Unit-M 2.0 with the RS232 and USB interface and programming adapters, and to join the I²C-Bus modules to each other and with the Unit M 2.0 or the Application Board.
Click For Info
Ideal attention grabber for advertisement (for example display windows). The LEDs can be individually separated and fastened with the attached adhesive tape. A light sensitive motion sensor sets off a sporadic sequence of running lights for approx. 15 seconds with 6 red LEDs.
Click For Info
Infra-red interface, RC5 compatible, hard wired to port 3 (transmit) and port 2 (receive). Control directly from the operating system is supported. Passend zu: A · 2.0 · 1.2
Click For Info
The module adapters are the interface of choice for the evaluation board, \"Mega 32\" Cat Item No: 19 82 45 and Mega 128 \"Order No.: 19 82 58 easy to expand. On the module adapter module, the extension of the C-Control I, which are designed as a 40-pin plug connectors are simply plugged into the...
Click For Info
The module adapters are the interface of choice for the evaluation board, \"Mega 32\" Cat Item No: 19 82 45 and Mega 128 \"Order No.: 19 82 58 easy to expand. On the module adapter module, the extension of the C-Control I, which are designed as a 40-pin plug connectors are simply plugged into the...
Click For Info
Temperature sensor for C-Control I 2.0 1-Wire Bus. Temperature range: 55 â 100 ºC Anschlusskabel 2 m vergossen.
Click For Info
With the complete C-Control I software (all units), including all Basic examples, drivers, manuals, documentation etc.
Click For Info
In applications where a second display is needed, or the hardware environment does not permit a directly connected display, this display can be driven on the I²C-Bus. In addition, the display can be driven at the C-Control I Micro (with the new operating system).
Click For Info
This module can be used to program all C-Control I 2.0 units through the RS232 connection. If a jumper is used, programming with null modem or 1:1 cable is possible.
Click For Info
Functional and neutrally printed front plate made of 1.5mm thick anodised aluminium for mounting with the C-Control I installation set.
Click For Info
This active module (2 oscillators, 1 monoflop) and a small Basic program allow you to check the function of all ports of your C-Control I M-Unit 2.0 (and 1.2 with Adapter) including IRQ, DA1, DA2, F1, F2. When you are not sure whether there is a fault or defect in your hardware or there is a...
Click For Info
Test board grid with 260 solder points for wiring your own applications. All the lines available on the BUS are labelled on both the mounting and soldering sides with the line names as used on the unit and specified in the operating instructions. Suitable for: A · E.
Click For Info
2 relays with a contact rating of 25 V/16 A, 2 x conv. connected with ports 5, 6. Suitable for: A · E · M · 2.0 · 1.2.
Click For Info
Input/output module with 1 x 8-pin (DIL) switch and 8 LEDs for simulating operating states. For ports 1 to 8. Suitable to: A
Click For Info
This module provides terminals to connect your application with the outside world. Terminal connections to ports 1 to 16, AD1 to AD8, +5 V and GND are provided. Suitable for: A · E.
Click For Info
Passive 5x distributor for distribution of the I ² C bus, RXD and TXD signals and the +5 V and GND. The distributor can be mounted with its mounting holes on the LCD or LED display (including installation kit). The 6-pin connector sockets are wired in parallel, so it is indifferent which one is...
Click For Info
This module is an active pull-up module and ensures steep signal flanks on the bus line when the lines are long with high capacitive load. With the line driver module, the rise time is kept below 1 µs at a bus capacitance of 200 pF. For higher bus capacitance (or longer line lengths), several...
Click For Info
Once constructed, this kit can be used to switch on 230V appliances such as a heater, heatpipes or similar when a set temperature is undershot. A KTY 81-220 temperature sensor (thermistor) determines temperature and the limits are set by the user via a trimpot. A separate trimpot can be used to...
Click For Info
Expands your application by adding 8 more byte ports (PCF8574) via the I²C Bus. The expanded ports can also be directly addressed by the operating system. Up to 8 of these modules are supported. Suitable for: A · E.
Click For Info
For a precise measurement of temperature of different applications in the range of -55 to 125 °C . The accuracy of measurement amounts to ±1 °C and in the temperature range of 0 â 70 °C an accuracy of even ±0.5 °C is reached. The resolution can thereby, be upto 0.06 °C,...
Click For Info
8 power drivers (2 W/24 V/DC, open collector) for I²C bus port expansion module (Order No. 19 88 48). For the expanded ports. This module is plugged into the port expansion module in piggyback mode. Passend zu: A · E:
Click For Info
.rm-cont h2, .rm-row h2{margin:0 0 10px}.u1, .u1-2{float:left}.rm-row{width:725px;overflow:hidden;padding:30px 0;border-bottom:1px solid #eee;clear:both;font-family:\"Helvetica Neue\", Helvetica, Arial, sans-serif;font-size:12px}.rm-row h2{font-size:22px!important}.rm-cont{padding:15px}.rm-cont...
Click For Info
Running out of spare HDMI ports on your TV? Need to connect an additional HDMI device such as a game console BluRay NAS or other device using the popular HDMI connector? The class-leading Dynamode HDMI switch is both eleg...
Click For Info
Low power adapter Low power plug - USB 2.0 port Mini B 5 mm 2.1 mm Conrad Components 1 pc(s)
Click For Info







